Precompletion Sound Testing Throughout London

Precompletion Sound Testing Throughout London 

To help enforce good acoustic design principles pre-completion sound testing was introduced July 2003, this resulted in all new build properties and conversions which were built after this date are require 10% of each party wall/floor construction type to be tested. APT Sound Testing undertake precompletion sound testing throughout London.

Precompletion Sound Insulation Testing is carried out between pairs of rooms separated by party walls or floors. The two ‘habitable’ areas that usually require sound testing are living rooms and bedrooms, although other rooms can be tested if this is not possible, i.e. kitchen to bedroom. Here is a quick description of the tests:

sound testing

Airborne Sound Tests

Airborne Sound Tests may be required between horizontally and vertically separated pairs of rooms. The sound tests are undertaken by using a sound source, amplifier and loudspeaker to generate a high noise level in one room (the source room). Noise measurements are then taken in both the source and receiver rooms using a prescribed number of source and microphone positions.

Impact Sound Tests

For vertically separated rooms, an Impact sound testing may also be required. This sound test is undertaken using a “tapping machine”, (as above) which drops a series of weights onto the floor of the upper room. The noise level in the lower (receiver) room is measured for a prescribed number of source and microphone locations. The background levels in the receiver room are measured and the reverberation time in the receiver room is also measured.

Required Sound Test Levels

The Building Regulation Part E set minimum performance requirements for sound insulation requirements between spaces. To help you better understand the sound level requirements of Part E, we have collated an easy to follow table – shown below.

Table 1a: Dwelling-houses and flats – performance standards for separating walls, separating floors, and stairs that have a separating function.

Airborne sound insulation
DnT,w+Ctr dB
(Minimum Values)

Impact sound insulation
L’nT,w dB
(Maximum Values)

Purpose built
Walls
Floors and Stairs

45
45

N/A
62

Material change of use
Walls
Floors and Stairs


43
43


N/A
64

Whatever the problem APT Sound Testing can usually find an acoustic solution that will satisfy Part E of Building Regulations. If you have a project that’s needs acoustic design advice or needs sound insulation testing then please contact us at: info@aptsoundtesting.co.uk or phone us directly on 0203 669 2650 and we should be able to offer you an expedient acoustic solution to help you achieve practical completion.

 

Pathway To Successful Sound Testing

Pathway to Successful Sound Testing 

We have undertaken hundreds of sound throughout London and the South East and have managed to streamline our pathway to successful sound testing. We also offer robust and cost effective acoustic design advice to ensure your compliance with Part E of Regulations. Our usual pathway for successful sound testing is:

1. Our Acoustic Design Service

2. Acoustic Site Audits

3. Precompletion Sound Testing

 

Acoustic Design Service

On our experience some of the most common mistakes during the construction are as follows:

  • Using lightweight blocks in the inner envelope construction as sound will travel along light block-work both vertically and horizontally from dwelling to dwelling.
  • The use of resilient suspended ceilings will help improve the performance of the floor partition.
  • Not incorporating a high quality resilient acoustic membrane on top of the floor to improve the impact performance of a floor.
  • Ensuring all penetration’s are fully sealed where they terminate through floors and they are adequately boxed with acoustic quilt and two layers of plasterboard.

sound testing equipment 

Acoustic Site Audits

We can undertake acoustic site audits, to let us view the existing site construction. This allows us to check for potential problematic areas such as the inclusion of lightweight blocks within the existing wall construction. It also lets us check that the installation teams are installing the acoustic materials as per manufacturer’s guidelines, thus avoiding crucial onsite mistakes. In our experience a sound test failure is often due to the poor workmanship rather than the actual design. The site survey visits negate the risk of sound test failure.

We can also undertake sample sound testing of the existing construction. This offers an accurate overview of the acoustic performance of the existing partitions, which enables us to offer a targeted acoustic design which takes into account the performance of the existing construction.

 

Defect Diagnosis & Remedial Advice

With many years’ experience in building acoustics, we are able to diagnose the reasons for the sound test failure and recommend a cost-effective solution. Often, the reasons for the partition failure are obvious to the test engineer in which case the advice will be minimal and subsequently the cost for acoustic design advice will be minimal. Sometimes, there are more technical issues which require more detailed diagnosis and invasive investigation, such as large amounts of noise flanking due to serious design faults, e.g. poor material isolation.

 

Precompletion Sound Testing

To help enforce good acoustic design principles pre-completion sound testing was introduced July 2003, this resulted in all new build properties and conversions which were built after this date are require 10% of each party wall/floor construction type to be tested.

Whatever the problem we can usually find an acoustic solution that will satisfy Part E of Building Regulations. If you have a project that’s needs acoustic design advice or needs sound insulation testing then please contact us at: info@aptsoundtesting.co.uk or phone us directly on 0203 669 2650 and we should be able to offer you an expedient acoustic solution to help you achieve practical completion.

 

Failed a Sound Test?

Failed a Sound Test?

If a client has failed a sound test, they often ask us for the reason why. It is almost certainly the result of a combination, of the following items:

  • Poor acoustic advice
  • Poor onsite installation
  • Flanking noise which comprises the sound insulating element.

Unfortunately, if you fail the sound testing its not easily rectified, as it usually means a major upgrade to the failed partition and thereafter another sound insulation test, which is both costly and time consuming.

If you do find yourself in this unfortunate situation, the first thing to do is contact APT Sound Testing your ‘friendly acoustic consultant’. We will be able to advise you on how to undertake minor acoustic upgrades, once we have obtained a copy of the failed sound test report. We can then ascertain the potential weak acoustic elements from the graphical results, and advise on a robust acoustic solution to building regulations Part E.

We will also be happy to liaise with your architect to ensure that all areas have been covered in the initial/remedial acoustic design. For a small fee we can visit site and undertake an ‘onsite design review’; or, do a an office based design review which cuts costs even further – to do this we would need all plans and sections relating to the project.

NoiseFlankingWall

Problems with airborne and structure borne sound are often associated with direct flanking transmissions through floors, supporting walls and other associated structures. You need to establish if your problem is due to direct transmission, flanking transmission or a combination of both so that the most effective remedial treatment can be chosen to suit.

First you need to understand how the sound is travelling into your home. It may be coming directly through the separating partition, i.e. wall or floor or it may be coming along another indirect route – called a noise flanking path. The most common such flanking path is the inner leaf of an external cavity wall.

If you have suffered a sound test failure and/or you require acoustic design advice then please email us in info@aptsoundtesting.co.ukor phone our design manager Darren on 07775623464. We have the experience, professionalism and acoustic know how to ensure that your project can achieve Part E of Building Regulations.

Sound Insulation Testing On New Build Dwellings In Compliance With the Code for Sustainable Homes

Sound Testing  On New Build Dwellings In Compliance With the Code for Sustainable Homes

Sound Testing is usually undertaken near the end of a project to show that the party wall and floors meet the Building Regulations. Approved Document E stipulated performance values.  The method for sound testing for airborne and impact sound insulation is in full accordance with: the suggested methods presented in BS EN ISO 140-parts 4 & 7: 1998.

Detached houses don’t require sound insulation testing, however if the house has been built on to the end of an existing house and/or terrace it usually requires 2 airborne wall tests – 1 through the lower kitchen/lounge and one through the bedroom walls on the upper floors.

Buildings such as apartment blocks often require airborne and impact sound insulations tests. Airborne sound insulation testing is normally required between horizontally and vertically separated pairs of rooms i.e. the wall and floor partitions. The sound tests are undertaken by using a sound source, amplifier and loudspeaker to generate a high noise level in one room (the source room). Noise measurements are then taken in both the source and receiver rooms using a prescribed number of source and microphone positions. The background levels in the receiver room are measured and the reverberation time in the receiver room is also measured. From the results, the airborne sound insulation (DnT,w + Ctr) is calculated and compared to the requirements of Approved Document E.

Thereafter impact sound testing may also be required for vertically separated dwellings. Impact sound insulation testing is undertaken using a “tapping machine”, which drops a series of weights/small hammers onto the floor of the upper room. The noise level in the lower (receiver) room is measured for a prescribed number of source and microphone locations. The background levels in the receiver room are measured and the reverberation time in the receiver room is also measured. From the results, the impact sound insulation (L’nT,w) is calculated and compared to the requirements of Approved Document E.

When it comes to refurbishment projects i.e. large houses converted into flats and/or an office block into flats we can undertake a sample sound test of the existing wall and floor construction. Once we have established the sound levels for the existing construction we can then look at extent of the acoustic upgrades to attain Part E Compliance. This is much more effective than just forwarding an acoustic design that may be to excessive and expensive, especially when the existing construction is already ‘acoustically’ robust and therefore only needs to improve by a 1-3dB.

sound testing

The sound insulation levels required to pass Part E are usually 45dB for airborne wall and floors and 62dB for Impact Sound Testing on new build, however sometimes a higher target may be required in-line with the Code for Sustainable Homes; this is usually in defined in the following figures +3, 5 & 8dB, this means if its plus 5dB you will need to achieve 50dB for airborne and 57dB for impact sound testing.  Obviously if you need to comply with the Code for Sustainable Homes then special attention must be shown to the acoustic design from the offset to reduce the chance of sound testing failure.

APT Sound Testing can help you to achieve this more robust design criterion. We can also help if your building fails the sound insulation testing by offering a targeted acoustic design solution saving time and potential costs.

If you have a project that requires sound insulation testing then contact us now, we can propose a sound testing schedule that should comply with Part E. Please contact us at: info@aptsoundtesting.co.uk or call us at 07775623464

Sound Testing On Refurbishment Projects

Sound Testing On Refurbishment Projects

When it comes to refurbishment projects i.e. large houses that have been converted into flats and/or an office block into flats, we can undertake a sample sound test of the existing wall and floor construction to ascertain the existing sound insulation levels. Once we have established the sound levels for the existing construction, we can then look at extent of the acoustic upgrades to attain Part E Compliance. This is much more effective than just forwarding an acoustic design that may be to excessive and expensive, especially when the existing construction is already ‘acoustically’ robust and therefore only needs to improve by a a minimal amount such as 1-3dB. By having the existing sound levels of the partitions we can recommend targeted, acoustic upgrades to comply with Building Regulations Part E.

This Video show some of the sound leakage paths

The sound insulation levels required to pass Part E for refurbishment projects are less stringent than new build projects. Instead of 45dB for airborne its 43dB (2 dB less), and for instead of 62dB for Impact Sound Testing its 64dB on new build (2 dB more).

On refurbishment projects you cannot use Robust Details, therefore sound testing has to be undertaken. Obviously due to the complex nature of refurbishment projects its best if you consult with us at the beginning as we can offer advice on how to upgrade the partitions to pass the sound testing.   We can also help if your building fails the sound insulation testing by offering a targeted acoustic design solution saving time and potential costs.

If you have a project that requires sound insulation testing then contact us now, we can propose a sound testing schedule that should comply with Part E. Please contact us at: info@aptsoundtesting.co.uk or call us at 07775623464

Sound Insulation Testing In Compliance With Building Regulations Part E.

Sound Insulation Testing In Compliance With Building Regulations Part E.

Sound Testing is usually undertaken near the end of a project to show that the party wall and floors meet the Building Regulations. Approved Document E stipulated performance values.  The method for sound testing for airborne and impact sound insulation is in full accordance with: the suggested methods presented in BS EN ISO 140-parts 4 & 7: 1998.

Detached houses don’t require sound insulation testing, however if the house has been built on to the end of an existing house and/or terrace it usually requires 2 airborne wall tests – 1 through the lower kitchen/lounge and one through the bedroom walls on the upper floors.

Buildings such as apartment blocks often require airborne and impact sound insulations tests. Airborne sound insulation testing is normally required between horizontally and vertically separated pairs of rooms i.e. the wall and floor partitions. The sound tests are undertaken by using a sound source, amplifier and loudspeaker to generate a high noise level in one room (the source room). Noise measurements are then taken in both the source and receiver rooms using a prescribed number of source and microphone positions. The background levels in the receiver room are measured and the reverberation time in the receiver room is also measured. From the results, the airborne sound insulation (DnT,w + Ctr) is calculated and compared to the requirements of Approved Document E.

sound testing

Thereafter impact sound testing may also be required for vertically separated dwellings. Impact sound insulation testing is undertaken using a “tapping machine”, which drops a series of weights/small hammers onto the floor of the upper room. The noise level in the lower (receiver) room is measured for a prescribed number of source and microphone locations. The background levels in the receiver room are measured and the reverberation time in the receiver room is also measured. From the results, the impact sound insulation (L’nT,w) is calculated and compared to the requirements of Approved Document E.

Impact Sound Testing

When it comes to refurbishment projects i.e. large houses converted into flats and/or an office block into flats we can undertake a sample sound test of the existing wall and floor construction. Once we have established the sound levels for the existing construction we can then look at extent of the acoustic upgrades to attain Part E Compliance. This is much more effective than just forwarding an acoustic design that may be to excessive and expensive, especially when the existing construction is already ‘acoustically’ robust and therefore only needs to improve by a 1-3dB.

The sound insulation levels required to pass Part E are usually 45dB for airborne wall and floors and 62dB for Impact Sound Testing on new build, however sometimes a higher target may be required in-line with the Code for Sustainable Homes; this is usually in defined in the following figures +3, 5 & 8dB, this means if its plus 5dB you will need to achieve 50dB for airborne and 57dB for impact sound testing.  Obviously if you need to comply with the Code for Sustainable Homes then special attention must be shown to the acoustic design from the offset to reduce the chance of sound testing failure.

APT Sound Testing can help you to achieve this more robust design criterion. We can also help if your building fails the sound insulation testing by offering a targeted acoustic design solution saving time and potential costs.

If you have a project that requires sound insulation testing then contact us now, we can propose a sound testing schedule that should comply with Part E. Please contact us at: info@aptsoundtesting.co.uk or call us at 07775623464

DESIGNING YOUR BUILDING TO PASS PART E SOUND INSULATION TESTING

Designing your Building to Pass Part E Sound  Insulation Testing

We at  APT Sound Testing often get asked what architectural features or plan arrangements can reduce the level of sound insulation or introduce additional sources that may cause us to fail our sound insulation testing.

Here is a quick list of the most common problems:

  • Internal stairs directly beside a separating wall – this can lead to footsteps being heard inside the adjacent dwelling, especially in bedrooms.
  • Using lightweight blocks on flats – lightweight blocks are often used in the construction of internal walls despite the block manufacturer’s warnings that they should not be used for the inner envelope or dividing wall construction. The walls are so lightweight they vibrate (almost like a snare drum) so sound can travel up or across the partition.
  • Chimney stacks, flues and fireplaces built within a separating wall – this can lead to sound traveling up the flue and being heard in flats above and/or below.
  • Recessed cupboards (presses) within a separating wall – this usually means that the width of the sound insulation is compromised which directly leads to a reduction in sound insulation levels.  
  • A flat spanning over several flats below, for instance a penthouse;
  • Communal stairs beside a separating wall – as this is a heavy trafficked area it can lead to footsteps being heard inside the adjacent dwelling, especially in bedrooms.
  • Communal vertical soil vent pipes and horizontal service pipes within a separating floor – if the services are not properly boxed out this can lead to general noise going straight through the floor as well as the noise of flushing water as it runs down the SVP pipes etc.
  • Lifts beside separating walls – this is often a bad scenario due to the higher start up current that’s needed to start a lift, this can cause a loud whine when the lift first starts and if there is insufficient sound insulation within the lift wall this will usually be heard by the adjacent resident/s
  • Water pumps used to raise water pressure – this can be problematic especially where a bedroom is located on the opposite side of the partition.
  • Chimney stacks, flues and fireplaces built within a separating wall – this is often a major cause of noise problems as they are often built quite close to each other thus reducing the mass of the separating wall/partition.  
  • Recessed cupboards (presses) within a separating wall – again this reduces the sound insulation levels as it reduces the mass of the wall partition.

It is worth noting that with careful consideration during the design phase most potential sound transference problems can be negated.

ACOUSTIC_DESIGN

Unfortunately, general exposure to excess amounts of noise from adjacent dwellings may act as a catalyst affecting the occupant’s health and well-being.  Noise that is unavoidable, unimportant or emotive is often the most annoying. Disrupted sleep and listening to television/radio are the most common noise-disrupted activities. Noise transmission between dwellings causes increased tension between neighbours and leads to disputes, which may result in physical assaults.

If you are unsure of your buildings acoustic design and/or you require sound testing contact APT Sound Testing at: info@aptsoundtesting.co.uk or call us on 07775623464

ACOUSTIC DESIGN FOR PRECOMPLETION SOUND TESTING

ACOUSTIC DESIGN FOR PRECOMPLETION SOUND TESTING

It’s extremely important that careful consideration is given to the acoustic design for pre-completion sound testing at an early stage of the design and construction process. It can be very problematic if the building fails the pre-completion sound testing just before buildings due to hand over.   To try and reduce the chance of a sound test failure APT can visit site to conduct a comprehensive acoustic design survey and  review. We also take this opportunity to meet; the site/project manager, architects etc. to go through the building’s design, site constraints and most cost effective method of achieving Part E of Building Regulations.

Our proactive acoustic design service, takes into account the build-ability, programme time and material cost. We ensure the relevant parties are fully aware of the installation detail required, highlighting possible ‘onsite’ construction problems and their prevention to achieve a successful installation and building sign off.

PROACTIVE SITE SUPPPORT

Once we have completed the acoustic design report our services don’t finish there. We provide the site team with on-going design support. You will have direct contact with the allocated acoustician from the start of the process through to the successful completion of the project.

Once the part of the building is completed we can undertake sample sound testing to ensure the design and onsite construction methods are sufficient to achieve a Part E sound test compliance.

THE DIFFERENCE BETWEEN LABORATORY AND ONSITE SOUND TESTING

Unfortunately, it is very difficult to construct acoustic details to the stringent standards of the laboratory. When the construction assembly is tested in the lab, it is also certified and an exact description of the materials and the installation techniques are described in detail and followed to the letter, obviously this should be replicated on the your site as closely as possible. However, it is not always possible to replicate the exact conditions on the job-site compared to the ideal conditions normally present in a lab setting, which is the reason why a 5dB point difference is allowed between the construction design on paper and the actual on site construction performance.

NOISE FLANKING

To try and work out if you have flanking sound you first need to understand how the sound is travelling into your home. It may be coming directly through the separating partition, i.e. wall or floor or it may be coming along another indirect route – called a flanking path. The most common such flanking path is the inner leaf of an external cavity wall.

Problems with airborne and structure borne sound are often associated with direct flanking transmissions through floors and supporting walls and other associated structures. It is essential to establish if your problem is due to direct transmission, flanking transmission or a combination of both so that the most effective remedial treatment can be chosen. If you are unsure where the sound is getting through, then contact us as we should be able to identify the worst areas by undertaking sound testing on the problematic partitions.

NoiseFlankingWall

Unwanted noise travelling along flanking paths makes the building structure vibrate and this causes the sound to radiate into your room. One solution is to build another wall or ceiling in front of the original, but not connected to it (often called an independent wall or ceiling). APT can help to locate the flanking sound and propose a cost effective design that will satisfy Part E of Building Regulations.

If you would like more information in regards to sound testing please also follow our blog at: http://soundtestinguk.blogspot.co.uk/, or contact us at: info@aptsoundtesting.co.uk or phone us on 07775623464 or visit our website at: www.aptsoundtesting.co.uk

OUR SOUND TESTING & NOISE SURVEY SERVICES

A SUMMARY OF OUR SOUND TESTING & NOISE SURVEY SERVICES.

Here at APT Sound Testing our clients often ask for a summary of our sound testing and noise survey services we undertake in compliance with Part E of Building Regulations . Here is a quick summary of our acoustic services:

We are UKAS accredited to carry out Sound Insulation testing for:

  • Houses and flats in compliance with Part E of the Building Regulations.
  • Houses & Flats in compliance with the Code for Sustainable Homes.
  • Classrooms within schools in compliance with BB93.
  • All commercial buildings in compliance with BREEAM.

We also carry out carryout various noise surveys to comply with the following:

  • Noise Surveys 8233 for Planning Applications.
  • Background Noise Surveys for Air Conditioning Plant.
  • Industrial Noise Surveys

The sound insulation levels required to pass Part E are usually 45dB for airborne wall and floors and 62dB for Impact Sound Testing on new build and 43dB for airborne wall and floors and 64dB for Impact for converted properties. Sometimes a higher target may be required in-line with the Code for Sustainable Homes; this is usually in defined in the following figures +3, 5 & 8dB. Obviously if you need to comply with the Code then special attention must be shown to the acoustic design from the offset. APT Sound Testing can help you to achieve this more robust design criteria. We can also help if your building fails the sound insulation testing by offering a targeted acoustic design solution saving time and potential costs.

sound testing

The amount of sound testing you require depends on the size of the development. All new build properties and conversions require 10% of each party wall/floor construction type to be tested, i.e. if you have 10 flats you would require 1 x 6 pack, this consists of 2 airborne wall, 2 airborne floor & 2 Impact sound tests. However if you have 11 units this would rise to 12 Sound Tests or 2 x 6 pack. Sometimes more tests may be required if you have many different types of walls and floors, however we will always try to propose the minimum testing required to comply with Part E.

Impact Sound Testing

We also offer planning noise surveys comply with BS8233 and BS4142, this allows us to provide all you acoustic requirements in one easy package; reducing cost and improving onsite co-ordination. Air Pressure Testing is UKAS accredited to undertake both Sound and Air Tightness Testing and is also accredited to ISO 17025:2005 ‘General requirements for the competence of testing and calibration laboratories’

 If you have a project that requires sound insulation testing and you are unsure how to comply with Part E of Building Regulations then contact us now, we can propose a sound testing schedule that should comply with Part E. If you are unsure of your projects acoustic requirements please click here at; info@aptsoundtesting.co.uk or visit our website at www.aptsoundtesting.co.uk  or call us at 07775623464

Sound Insulation Testing – Questions & Answers.

 Sound Insulation Testing – Questions & Answers.

APT sound testing often get asked a similar bunch of questions in regards to sound insulation testing. Over the last couple of years we have collated these questions and answers and to help our valued clients we have shown these below.

What is sound testing for Part E
Sound Insulation Testing is a method of quantifying the sound insulation performance of  walls and/or floors. Sound testing can be carried out on party walls, party floors or facades of any building.

What is sound insulation?
Sound insulation is the property of a wall and /or dividing partition to resist the passage of noise.

Why do I need sound testing on my Project/Property?
The largest single reason for disputes between neighbours is noise complaints. Approved Document Part E – Resistance to the passage of sound describes minimum standards to be achieved by newly built domestic dwellings.

What building regulation do we work to?

Approved Document Part E, sets out minimum standards for sound insulation performance to be achieved by party wall and party floors. Building contractors may show compliance with Part E of the Building Regulations by two methods. One method is to register plots to be built with Robust Standard Details Limited and the other is to show as-built performance by Pre-Completion Sound Testing to Part E of Building Regulations.

When are Pre-Completion Sound Tests carried out?
Pre completion Sound testing is carried out when the construction of party walls and floors are largely complete. Windows should be in place with any vents closable. Internal and external doors should be in place, along with skirting, cornicing and plug sockets in place. Sound testing on floors must be carried out before any soft coverings are in place.

 Do detached properties require sound testing for Part E of Building Regulations?

No, only attached properties require sound tests, detached properties share no common partitions with any other properties.

Are internal walls/floor between rooms within a single dwelling sound tested?
No, Laboratory test based performance standards (Rw) exist for certain internal walls and floors, but they are not intended to be verified as-built by on site measurement and therefore sound insulation testing is not a requirement.

How many sound tests are needed on my Project?

Approved Document E states that one set of sound tests is required for every 10 units in a group or sub-group. A group or sub-group is defined where significant differences in construction or layout occur, for instance:

  • For a pair of semi-detached Houses – a set of tests would usually comprise two airborne sound insulation tests of a separating wall.
  • For Flats (up to 10 units) – a six pack would normally be required, this comprises of: two airborne wall tests, two airborne floor tests and two impact floor sound tests. The easiest way to work out the number of tests required is to multiply 1 x 6 packs for every 10 flats, i.e. if you have 22 flats you will require 3 x 6 packs which equals 18 sound tests in total.
  • For Rooms for Residential Purposes (student accommodation, hotel rooms, care homes etc.) – a set of tests would usually comprise: one airborne sound insulation tests of a separating wall; one airborne sound insulation test of a separating floor; one impact sound transmission test of a separating floor.

How are plots selected for sound testing?
We will usually specify the sound insulation tests that are required. We first look at the plans then work a testing schedule taking into account testing through both the projects lounges & bedrooms where possible. We will also try and undertake testing across walls and floors in different areas of the building. The building control officer, warranty provider or other concerned parties may require you to carry out sound testing in specific areas or plots. However where this has not been stipulated we can advise accordingly. When we have specified the sound testing schedule it should always be checked by building control and/or the client to seek their approval before the commencement of testing.

How do I Preparing my Site for Sound Insulation Testing?

APT always send out a checklist with our fee proposals to help you prepare for the sound testing, as we always want our clients to be fully prepared so they can pass their sound testing at the first attempt.

 

Will the sound insulation testing disrupt work on site? 
There should be minimal site disruption during the sound insulation testing. However, although high levels of noise are generated but in order to make accurate test measurements, relatively quiet conditions are needed to take accurate measurements. This means that anyone working in the testing area will have to leave temporarily and any noisy works in the vicinity of the test rooms will need to be halted i.e. using power tools.

How long will the sound testing take?

The time taken for London sound testing varies with site conditions, but generally a ‘6 pack’ set of tests on houses and flats takes about one to two hours. Obviously this depends on the site being fully prepared in line with our sound testing checklist.

How do I know if I’m ready for a sound insulation test?
The plots should be at least at second fix stage – for further details please refer to our checklist.

Do I need all internal and external doors and windows installed?
Yes, all internal and external doors must be fitted and operable prior to the sound testing. Trickle vents must also be installed where required.

 What if I only have 110 volt on site?

Unfortunately we cannot undertake the testing; we will need 240V to undertake the sound insulation testing.

Should I inform my neighbours of the impending sound testing?
If the building is attached in any way to occupied properties then you will need to inform the neighbours. To comply with Part E we need to gain access to the neighbouring properties to undertake the sound test. You will need to ensure that access is provided to the neighbouring properties throughout the sound testing.

Can you offer advice to help me to pass my sound insulation testing?
We offer an acoustic design service to help you design your buildings partitions to pass Part E sound testing. If you send through the relevant drawings such as sections and plans during the design stages of the project, we can check the design to see if there are any junctions or details where ‘noise flanking’ may occur. You can then change your design to lower the chance of a sound test failure.

Do you have a check-list to help us prepare for the sound testing?
Yes, we have an informative checklist to help prepare for the testing, please visit our website at www.aptsoundtesting.co.uk to download the checklist.

Is it easy to upgrade the sound insulation in my Existing Home?.

Yes of course. If excess noise is causing you stress and anxiety, in comparison upgrading the walls/floors to your existing property can be a worthwhile process. its normally quite easy to upgrade walls and floors/ceilings to lower sound transmission. Sometimes it can be as easy as installing an acoustically (insulated) backed board against the offending partition. In all instances it is important not only that the right products are used to cause minimal disruption but they are also fitted correctly in-line with manufacturer’s guidelines. .

Rest Assured

We believe in working with our clients whether they are existing home owners suffering acoustic problems or large developers requiring a more expansive service to achieve sound testing compliance. We believe that by being involved at the beginning of a project we can often save our clients expensive and difficult remedial works at the completion stage of a project.

If you would like more information on our full range of services please contact us now at info@aptsoundtesting.co.uk or call us on 07775 623464