Good Acoustic Design Detailing

Good Acoustic Design Detailing.

Careful consideration to acoustic design detailing should be used from the offset of the project, whether it’s a new build or conversion project, if the acoustic design is taken into consideration from the offset of the project then it usually results in compliance with Building Regulations Part E.

architect drafting a house blueprint

To help our clients achieve a successful sound test at the first attempt, we offer a full acoustic package which consists of the following elements:

  • Site Survey Visits – to let us view the existing site construction. This allows us to check for potential problematic construction such as inclusion of lightweight blocks in the existing construction. It also lets us check that the installation teams are installing the acoustic materials as per manufacturer’s guidelines.
  • Sample Sound Testing – of the existing construction. This offers an accurate overview of the acoustic performance of the existing partitions which enables us to offer a targeted acoustic design using the sound insulation performance of the existing construction.
  • Acoustic Design Review – a full design review of the proposed developments party walls and floors.

There are many design considerations that need to be accounted for when allowing for your project/s, they are:

  • Avoid the use of lightweight blocks in the inner envelope construction as sound will travel both vertically and horizontally from dwelling to dwelling.
  • The use of resilient suspended ceilings will help improve the performance of the floor partition.
  • Ensure all support steels/timbers are carefully boxed out where they travel from flat to flat vertically and horizontally.
  • Use a high quality resilient acoustic membrane on top of the floor to improve the impact performance of a floor.
  • Ensure all penetrations are fully sealed where they terminate through floors and they are adequately boxed with acoustic quilt and two layers of plasterboard.

If you have a project that’s needs acoustic design advice or sound testing in London, then please contact us at: info@aptsoundtesting.co.uk or phone us directly on 07775623464.

Acoustic Design Advice for my Sound Insulation Test

Acoustic Design Advice for my Sound Insulation Test

We at APT Sound Testing pride ourselves on offering a comprehensive acoustic design service to help you development attain compliance with Building Regulations Part E at the first attempt. If you send through the relevant drawings such as sections and floor plans during the design stages of the project, we can check the design is adequate and if there appears to be any junctions or details where ‘noise flanking’ may occur, we can then advise if any changes are required to lower the chance of sound test failures.

Acoustic_Design_Service

There are many factors to consider when considering good acoustic design, and they are usually split up into five key factors. If used together or in various combinations they will improve sound insulation properties over a wide range of frequencies. The main factors are:

  1. Mass
  2. Isolation
  3. Absorption
  4. Resilience
  5. Stiffness

Coupled_wall_construction

Also, noise flanking transmission may in some cases be the dominant pathway between adjoining dwellings, especially in existing buildings where you are planning to convert offices/large houses into flats. Here are just a few of the potential noise flanking areas:

  1. Structural Steels
  2. Windows built very close to Internal partitions
  3. Inner leaf of the external wall
  4. External wall cavities
  5. External façade or outer leaf
  6. Roof structure

APT Sound Testing can advise on all types of acoustic design, whether it’s during the initial design of a new build project and/or undertaking sample sound testing and design during a refurbishment/renovation project. We also undertake UKAS accredited sound insulation testing providing a ‘one stop’ solution for all your acoustic requirements.

If you would like more information on our full range of our acoustic services please contact us now at info@aptsoundtesting.co.uk or call Darren direct on 07775 623464.

How are Plots Selected for Sound Testing?

How are plots selected for sound testing?

APT usually specifies the amount of sound insulation tests that are required. Firstly we look through the floor plans to work out a testing schedule taking into account the positioning of habitable rooms, the room and partitions sizes. We always tests through ‘habitable rooms’ partitions i.e. lounges & bedrooms wherever possible – as per the details shown below). We will also try and undertake testing across walls and floors in different areas of the building and through different partition types i.e. if one wall is made of masonry and the other met-sec partitioning.  Once we have specified the sound testing schedule, the client should show building control to seek their approval before the commencement of the sound testing.

Detail A – Sound Testing through Walls

Plan_Sound_Test_Through_Walls

Detail B – Sound Testing through Floors

Plan_Sound_Test_Through_Floor

What are the minimum requirements for separating party walls and floors?

The minimum requirements of ADE can depend on a variety of factors such as if the development is new build or refurbished, whether the development is intended to be a permanent dwelling, or classified as “rooms of residential purposes” (e.g. hotels, student accommodation, etc). A brief summary of the minimum requirements can be found below:

DWELLING HOUSES AND FLATS Airborne standard

DnTw,w+Ctr dB

Impact Standard

L’nT,w dB

 

Purpose built dwellings

Walls at least 45 N/A
Floors and Stairs at least 45 up to 62
 

Dwelling formed by material change of use

Walls at least 43 N/A
Floors and Stairs at least 43 up to 64

 

ROOMS FOR RESIDENTAIL PPOSES Airborne standard

DnTw,w+Ctr dB

Airborne standard

L’nT,w dB

 

Purpose-built rooms

Walls at least 43 N/A
Floors and Stairs at least 45 up to 62
 

Rooms formed by material change of use

Walls at least 43 N/A
Floor and Stairs at least 43 up to 64

If you have a project that requires acoustic design advice or sound insulation testing, then please contact us at: info@aptsoundtesting.co.uk or phone me directly on 07775623464.

Approved Document E: Frequently Asked Questions

Approved Document E: Frequently Asked Questions

Why am I required to undertake sound insulation testing?  

Sound insulation and speech privacy are critical for a variety of reasons. Inadequate sound insulation can be extremely distressing to those affected by it and may lead no major noise disputes and legal actions. For example, in an apartment block, your upstairs neighbour may like playing loud music. However, the downstairs occupant may be working nights and sleeping throughout the day, thus any inadequate sound insulation between these two flats would cause great disturbance and distress to the downstairs occupants.

Noise_Problems_Failed_Sound_Testing

 What is precompletion sound insulation testing?

Precompletion sound testing is a building regulation requirement for all new build and dwellings formed by ‘material change of use”, i.e. conversion projects. It has been a requirement that you undertake sound testing on dwellings since 2003. Sound testing should be undertaken to 10% of properties in each development to ensure that the separating walls & floors between habitable rooms of neighbouring properties meet the minimum requirements as defined by Approved Document E, commonly referred to as Approved Document E; for instance:

  • For a pair of semi-detached Houses – a set of tests would usually comprise two airborne sound insulation tests of a separating wall.
  • For Flats (up to 10 units) – a six pack would normally be required, this comprises of: two airborne wall tests, two airborne floor tests and two impact floor sound tests. The easiest way to work out the number of tests required is to multiply 1 x 6 packs for every 10 flats, i.e. if you have 22 flats you will require 3 x 6 packs which equals 18 sound tests in total.
  • For Rooms for Residential Purposes (up to 10 rooms) (student accommodation, hotel rooms, care homes etc.) – a set of tests would usually comprise: one airborne sound insulation tests of a separating wall; one airborne sound insulation test of a separating floor; one impact sound transmission test of a separating floor.

Sound_Testing_Flats

If you would like more information on our full range of our acoustic services, including sound testing, acoustic design and noise surveys, please contact us now at info@aptsoundtesting.co.uk or call Darren direct on 07775 623464.

Upgrading Floor Partitions to Pass Sound Testing

Upgrading Floor Partitions to Pass Sound Testing

In our experience of undertaking hundreds of sample of sound tests throughout London and the Home Counties, refurbishment projects usually achieve 30-35dB for airborne sound and 70dB for Impact Sound, if the existing construction has not been acoustically upgraded. Unfortunately, the aforementioned figures do not meet the required 43dB & 64dB as stipulated in Part E of Building Regulations. As sound double every 10dB this is a massive failure and acoustic improvements must be made. Many existing construction consist of a similar construction as shown in as detail 1 below.

Detail 1: Existing Floor Partitions Rated at Approx. 30dB

Failed_sound_Testing_Due_to_existing_floor_Construction_

Improving Existing Floor Partitions

To reduce airborne and impact sound transmission this usually means adding density and isolation to the floor construction. This can be as simple as adding a drop ceiling consisting of 125mm timber frame. The top of the frame must be a minimum of 25mm below the existing ceiling finish – such as lathe and plaster. Then, to the inside of the timber frame add 100mm of Acoustic Wool and two layers of sound-board tacked to the bottom of the timber frame – all boards to be lapped. This should improve your sound test results by approx. 10-15dB depending on the existing site conditions and quality of the installation – as per Detail 2 below:

Detail 2: Acoustic Flooring Partition Upgrade

ceiling_upgrade_to_pass_sound_test

Taking the above into account is it essential that good acoustic design is addressed right from the start of the refurbishment project, so it prevents delays in handover, i.e. to prevent the dwelling failing the sound testing at building control signoff stage.– a common problem.

If you would like advice on your acoustic design or require sound insulation testing in London, please contact us now on 07775623464 or contact us at info@aptsoundtesting.co.uk.

 

A Successful Sound Insulation Test

A Successful Sound Insulation Test

There are many considerations to achieving a successful sound test on your development. The main areas that need to be addressed are the dividing wall and floor construction.

When dealing with walls you normally just need to worry about airborne sound; however with walls it’s both airborne and impact sound which can be far more difficult to deal with.

sound_transmission_through_floors

The usual noise problems associated with airborne sound transmission is TV noise, music and speech. This can be dealt with by applying ceiling treatments as well as mass and isolation to the building components. Impact sound (footfall) performance is increased by the used of resilience layers and isolation of components to prevent noise flanking through the partition.

Airborne Sound Testing

For airborne sound insulation testing Building Regulation Part E requires you achieve at least 45dB for new build properties and 43dB for conversion developments, this applies both to party walls and floors between properties. This level is the difference between the source level and the receiver level during sound testing. Impact Sound TestingThe measurement is corrected for several factors such as background noise, room characteristics and frequency weighting, giving the final sound insulation performance value of the tested partition. In this case the higher the number the better the sound insulation performance. The measurement is done by using a Class 1 Analyser and the associated equipment.

Impact Sound Insulation Testing

For impact sound insulation testing Building Regulation Part E requires you achieve at least 62dB for new build properties and 64dB for conversion developments. Impact insulation performance only applies to party floors and related to the effectiveness of the floor construction in absorbing shock such as footfall noise.Sound_Insulation_Testing_Equipment

Good Acoustic Design

To try and ensure you meet the standards stipulated within Building Regulations Part E, careful consideration should be shown to the acoustic design detailing from the start of the project. Tackling the acoustic design for both new build and conversion project requires two different construction techniques and acoustic design detailing. With new build properties you have a blank canvas in terms of the overall design whereas with conversions you usually need to work with the existing’ onsite’ construction which can be quite difficult.

We offer an acoustic design package, which contains the following elements:

  1. Sample Sound Testing – of the existing construction. This offers an accurate overview of the acoustic performance of the existing partitions which enables us to offer a targeted acoustic design using the sound insulation performance of the existing construction.
  2. Acoustic Design Review – a full design review of the proposed developments party walls and floors.
  3. Site Survey Visits – to let us view the existing site construction. This allows us to check for potential problematic construction such as inclusion of lightweight blocks in the existing construction. It also lets us check that the installation teams are installing the acoustic materials as per manufacturer’s guidelines.
  4. Final Precompletion Sound Testing in compliance with Building Regulations Part E.

If you have a project that’s needs acoustic design advice or sound insulation testing, then please contact us at: info@aptsoundtesting.co.uk or phone us directly on 07775623464.

We have also started our new facebook page at: https://www.facebook.com/APT-Sound-Testing-1705040043131199/

Careful Acoustic Installation leads to Successful Sound Testing

Careful  Acoustic Installation leads to Successful Sound Testing

It is very important that acoustic installation details are closely followed to ensure that the onsite results are as close as possible to the laboratory target. It is pointless having good acoustic design detailing if this is not carefully followed on site.

Acoustic_Design_Service

The following list explains what should during the onsite construction process to achieve a successful onsite sound tests and Part E compliance:

  1. Ensure that the construction team is fully briefed of the acoustic details.
  2. Ensure that the manufactures installation booklet is on site at all times.
  3. Ensure that the Acoustic floor is fitted with staggered joints.
  4. If you are installing floating screed ensure all isolation layer joints are overlapped and taped.
  5. Ensure all the Acoustic floor is sealed watertight even around heating pipes.
  6. Do not nail or screw through an Acoustic Floor.
  7. Do not screws plaster board into joists, when using a Resilient Bar system.
  8. Ensure the insulation fills the whole width of void
  9. Pack around pipe work and double board with staggered joints.
  10. Ensure that the plasterboard on any walls is complete right down to within 5-10mm of the subfloor and seal all gaps.
  11. Ensure you use the isolation tape around the wall of each room.
  12. Ensure plasterboard is fitted with staggered layers and all joints sealed.
  13. If using Resilient Bars ensure that they are fitted as per manufacturer’s recommendations.
  14. Ensure all Fireplaces are blocked up with brick or a twin lined plasterboard system and filled with acoustic insulation.
  15. Ensure that any RSJ’s or supporting steel work is insulated and isolated from plasterboard.
  16. Ensure all waste pipe service runs are boxed in with insulation and plasterboard.
  17. Ensure all doors and windows are installed before the test is carried out, to stop noise transference.

We offer an acoustic design service which includes site visits to make sure the acoustic elements are being installed as per the manufacturer’s guidelines. If you are worried about passing your sound testing at the first attempt please don’t hesitate to contact us now at: info@aptsoundtesting.co.uk or call Darren Direct on 07775623464.

The Difference Between Laboratory and Site Sound Testing

The Difference Between Laboratory and Site Sound Testing

Many suppliers of acoustic insulation products quote laboratory sound test results  to demonstrate the performance of their systems. This often causes considerable confusion regarding how well products will perform as there are usually large differences between the laboratory and site conditions. For instance laboratory sound tests do not take account of flanking sound and therefore produce sound insulation figures that would be very difficult to achieve on site.

sound testing

Despite site contractor’s best endeavours, it is extremely difficult to build to the stringent exacting standards of the test laboratory. When the construction assembly is undertaken in the lab, it has gone through an exacting installation technique prior to the sound test, which is also a contributing factor why better sound testing levels are achieved.

Throughout the acoustic installation the manufacturer’s guidance is followed to the letter by the lab technicians. Although, this should be replicated on site, it seldom is due to time constraints etc. and so a design which can be easily in excess of the requirements of approved document E, can often lose approx. 8-10dB compared to the laboratory results. Unfortunately there may be many reasons for poor sound test results such as poor quality site installation as well as other on-site issues where cost, time and programming constraints may come into play.

architect drafting a house blueprint

architect drafting a house blueprint

One important thing to consider is that most building structures will be subject to varying amount of flanking sound, so field sound test data should show the real performance of a system in a building. Laboratory sound insulation tests simply measure sound and do not account for flanking sound transmission.

If you are worried about your projects acoustic design and/or have questions about the precompletion sound testing, please don’t hesitate to contact us now at: info@aptsoundtesting.co.uk or Darren direct on 07775623464. 

How to Improve your Sound Test Results

How to improve your Sound Test Results

If you have started a new or conversion development, it is important that from the offset you realise that you will need to comply with stringent sound insulation requirements of Approved Document E. Both new and converted residential dwellings use must meet the standards stipulated in Approved Document E. Part E states that the separating floor partition (floor between two separate dwellings) must achieve sound insulation figures of 45dB for airborne sound and 62dB for impact sound on all new builds and 43dB for airborne sound and 64dB for impact sound on converted dwellings; if you don’t achieve the aforementioned results then you will pass the sound testing. 

Building Control will expect you to demonstrate compliance with Approved Document E 2003 by undertaking an independent sound insulation test to prove that you have met the standards for sound insulation between dwellings.

Sound_Insulation_Testing_Equipment

The sound testing must only be carried out by either UKAS or ANC approved companies. If the sound tests are not carried out by approved compaines then Building Control may not accept the sound test report and subsequently it may need to be undertaken again by an approved company costing more time and money.

We are UKAS accredited to undertake sound insulation testing as well as air tightness testing. We offer design advice to help our client achieve Part E sign off. In some cases clients instruct us to proceed with the sound testing, without having carried our any acoustic upgrades or remedial works often resulting in their partitions failing the sound test.

Sound_Testing_Semi_Detached_House

If you are worried about passing your sound testing in London at the first attempt please don’t hesitate to contact us now at: info@aptsoundtesting.co.uk or visit our website at: www.aptsoundtesting.co.uk or call Darren Direct on 07775623464.

Sound Intrusion Though Windows

Sound Intrusion Though Windows

Sound intrusion though windows can also be a source of great annoyance if the sound is excessive, and in some cases developments have failed the sound insulation testing due to poorly specified and installed windows. Sound intrusion may be down to a variety of factors. If the windows are operable types, the first thing to check is to see if the widows close properly against their seals and any weather stripping is continuous and in good order. If the window leaks air, then more often than not it will usually leak sound. If the window closes to form a tight seal and the weather-stripping seems adequate the next thing to check is the window frame. Windows are frequently installed in to the wall opening with plastic shims to insure the unit is plumb and level. In high traffic areas you will normally require a double glazed unit as a minimum and in some cases a triple glazed unit will be required.

Sound_Intrusion_Through_Windows

The space between the frame and the wall should be insulated and sealed before the window casings are installed. If this was not done correctly you can probably detect the sound leakage by placing your ear close to the frame and listening. The sound may be able to run along the cavity and back into the adjacent property, It is case of letting your ears do the walking and listening. If you detect distinguishable differences in sound you may have found the problem; the solution will be to remove the casing and insulate and caulk all leaks. In some cases the thickness of the glass maybe the problem in which case it may be necessary to install another layer of glass on the inside of the existing frame making sure that the additional pane of glass is well sealed into the opening.

In some instances you may be able to lower excessive sound by installing a heavy curtain – especially if the house is in a conservation area and as a result the local authority will not let you change or upgrade the windows.

If you require more advice on your project and/or you require precompletion sound testing, please contact us at: info@aptsoundtesting.co.uk  or phone me directly on 07775623464.