The different types of Sound Testing

The different types of Sound Testing.

There are two distinct types of noise to consider through floors, they are:

  • Airborne Noise (for example speech and music) and
  • Impact Noise (for example footsteps directly on the floor above)

To take this into account there are two different types of Sound Testing required in compliance with Approved Document Part E. Even if both types of sound are emitting through the ceiling/floor then there are some easy installations that should reduce the sound levels and improve your sound test results.

sound testing equipment

To help our clients overcome this problem, we also offer our acoustic design service which helps clients to pass the sound testing upon completion of the acoustic upgrade. By advising on a simple cost effective wall and/or floor upgrade, we are able to forward simple to follow acoustic design reviews, utilising our extensive knowledge of different materials and construction methods. Using this philosophy, to date, we have had no sound test failures where our acoustic upgrades have been incorporated into the site construction, ensuring compliance with Part E of Building Regulations.

Pre-completion sound testing has been a mandatory requirement since July 2003 and all new build properties and conversions which were built after this date require 10% of each party wall/floor construction type to be tested. The Sound testing is to be carried out between pairs of rooms separated by party walls and/or floors. Part E stipulates that it sound testing should take place between dividing partitions between living rooms and bedrooms as these are classed as the two main habitable rooms; however, other rooms can be used if this is not possible such as dining rooms, kitchen and studies.

APT Sound Testing can undertake UKAS accredited Part E sound testing throughout England and Wales. Our sound test engineers carry all the latest class 1 acoustic equipment and we provide full UKAS accredited air and sound testing, so our clients can be sure that all testing is completed to the strictest  ISO quality controlled standards.

If you would like advice on your acoustic design or sound testing in London, please contact us now at info@aptsoundtesting.co.uk or call us on 07775623464

Simple Design Solutions to Pass Part E Sound Testing

Simple Design Solutions to Pass Part E Sound Testing

There are many simple solutions to reduce the noise levels and achieve compliance with Part E sound testing. We can provide easy to follow acoustic design reviews, utilising our extensive knowledge of different materials and construction methods.

Our clients often convert large houses into multiple flats, i.e. a flat on each of the ground, 1st and 2nd floors. They usually leave the floor boards in place and install a layer of plasterboard to the underside of the existing plasterboard/lathe and plaster. Unfortunately this simple type of upgrade usually achieves 30dB for airborne sound, which will result in sound testing failure. The sound test result needs to be 43db and above for airborne noise and 70dB for Impact sound.

Failed_sound_Testing_Due_to_existing_floor_Construction_

One simple solution to overcome the above problem would be to add another ceiling element to the overall construction. This can be achieved by incorporating resilient metal bars which are connected to the underside of the joists and mounted perpendicular (90˚) to the joist direction. If plasterboard has already been tacked to the underside of the joists you can firstly add timber batten and then add the resilient bars, also mounted perpendicular (90˚ to the batten, thereafter 2 x 12.5mm layers of soundboard can be tacked to the underside of the resilient bar and an acoustic insulation added to the newly formed void. In between the joist void add 100mm acoustic insulation. Above the floor boards add an acoustic resilient membrane to lower the chance of impact noise transmitting down to dwelling below.

Acoustic_Ceiling_Upgrade

The aforementioned acoustic design solution will usually result in successful sound testing and compliance with Approved Document Part E.

If you require more information in regards to sound testing and/or acoustic design on your project please visit our site at www.aptsoundtesting.co.uk or contact us at info@aptsoundtesting.co.uk, or call me direct on 07775623464.

Poor Acoustic Design

Poor Acoustic Design 

Sound test failure is often down to poor acoustic design detailing during the design and construction phase of a project.

Sound test failure are often associated with poor acoustic design which allows noise flanking transmission through dividing floor and wall partitions. Unwanted noise travelling along flanking paths can make the building structure vibrate which causes the sound to radiate into your room. One simple cost effective solution is to build another wall or ceiling in front of the original, to offer extra isolation. For this upgrade to work you need to make sure that the independent wall or ceiling is not directly connected to the existing failed partition; so it provides isolation between materials.

ACOUSTIC_DESIGN

One of the main reasons for excessive noise flanking down to the use of lightweight blocks in the construction of the wall construction. Due to the lightweight mas of the inner wall it allows sound to transmit from dwelling to another, both vertically and horizontally. If a building has failed its sound testing, it is essential to establish if the problem is due to direct transmission, flanking transmission or a combination of both so that the most cost and time effective remedial treatment can be designed and applied to the failed partitions.

One way to reduce the chance of sound testing failures due to excessive noise flanking transmission is through a careful consideration to the acoustic design at the start of the project.  Unfortunately, by simply specifying high performance wall and floor partitions, it is no guarantee to adequate sound isolation and successful sound testing.

APT offer preconstruction design advice to help you achieve successful sound testing in London in-line with Building Regulations Part E. We also offer onsite inspection services to ensure that the sound insulation elements are being installed as per manufactures guild-lines, as its not use having a robust design if it not being installed properly on site.

If you require more information in regards to sound testing and/or acoustic design on your project please visit our site at www.aptsoundtesting.co.uk or contact us at info@aptsoundtesting.co.uk, or call me direct on 07775623464.